Fix error 0x8007045d
0x8007045d is ERROR_IO_DEVICE, Win32 error 1117: the request could not be performed because of an I/O device error. Windows could not read from or write to a storage device. Copy important data off first, then change the cable and USB port, run chkdsk with /f, and update the storage or USB controller driver.
Checked November 10, 2026 against the manufacturer's own pages.
The short version
What to install and where it comes from. Every link goes to the manufacturer or Microsoft, never to a copy.
Official files only, nothing bundled
Step by step
Save your data while the drive still reads
An I/O error can be the first sign of a failing drive. Before any repair, copy irreplaceable files from it to another disk or to OneDrive, starting with the most important ones.
Change cable, port and hub
Plug the drive straight into a port on the PC, not a hub or monitor port. Use a rear USB port on a desktop and try a different cable. For an SD card, try another reader and check the lock switch on the card.
Run chkdsk on that drive
Open Terminal (Admin) and run chkdsk E: /f, replacing E with the drive letter shown in File Explorer. Add /r to also look for bad sectors; this takes much longer. Microsoft notes that chkdsk /f needs the volume locked, so close files on it first.
Update the storage and USB drivers
Right-click Start, Device Manager. Under Disk drives and Universal Serial Bus controllers, right-click the entries for the drive and choose Update driver, Search automatically. Also check your PC maker's support page for chipset and card reader drivers.
Test the drive in another PC
If the same error appears on a second computer with a different cable, the drive is the problem. Check it with the maker's diagnostic tool and replace it if it reports failures.
Faster option: let a PC tool do the clean-up
The steps above fix this error. Errors like this often come back on a PC full of junk files, broken registry entries and leftovers from removed programs. A maintenance tool clears those in one scan.
Scan and clean up Windows
Finds junk files, invalid registry entries, startup slowdowns and privacy traces, then fixes them in one click.
Auslogics BoostSpeed 14 · Free version · Windows 11, 10, 8, 7 · 30-day refund on Pro
What triggers ERROR_IO_DEVICE
Windows asked a storage device to read or write a block of data and the device, or the path to it, reported failure. Microsoft’s message for 1117 is short: the request could not be performed because of an I/O device error. Unlike a permission or format problem, this one sits at the hardware level, so the fixes are about connections, drivers and the health of the drive.
Cable, port, controller or drive?
Change one thing at a time. If a new cable or port fixes it, the old connection was at fault. If the drive works on another PC, the first PC’s USB controller, card reader or power supply to the port is the suspect, and updated chipset drivers from your PC maker are the next step. If the drive fails everywhere, the drive is the cause. External hard drives that click, slow down or disconnect while copying are showing typical signs of a mechanical problem.
A less common cause: not enough USB power
Portable hard drives draw power from the USB port. Front panel ports, long cables and unpowered hubs may not supply enough during long copies, which makes the drive reset partway and Windows report an I/O error. Use a short cable on a rear port, or a powered hub. Some drives ship with a Y cable that uses two ports for extra power.
Questions
Does 0x8007045d mean my drive is dying?
It can. ERROR_IO_DEVICE means the device itself failed the read or write. Loose cables, weak USB power and faulty readers cause it too, so rule those out before you replace the drive.
Why does copying stop at the same file every time?
That file probably sits on a damaged area of the disk. Skip it and copy the rest. chkdsk /r can mark the area as bad, but the data in it may not be recoverable.
Can I fix 0x8007045d with a format?
Formatting can clear file system damage, but it erases everything and does not repair worn hardware. Only format after your data is safe, and keep testing the drive afterward.
Why does a backup fail with 0x8007045d?
The backup reached a sector it could not read or write, on the source or the target disk. Run chkdsk on both and try a different backup drive.